Good day! I present to your attention specification of equipment, products and materials made in AutoCad in DWG format. This specification is made in accordance with Form 1 - GOST 21.110-2013 (current). This GOST has been adopted in all CIS countries except Ukraine.
Describe in detail how the specification should be filled out, for which sets of working drawings the specification should be drawn up, etc. I don’t see the need, you will find all the necessary information in GOSTs, which you can find in the archive provided. The purpose of this article is to provide ready-made specification forms for use.
In Ukraine, the regulatory document DSTU B A.2.4-10-95 (GOST 21.110-95) is in force. This GOST replaces: GOST 21.109-80, GOST 21.110-82, GOST 21.111-84. The equipment specification must be carried out in accordance with Form 1.
As we see, there are not too many cardinal differences. The size of the graph and the name have been slightly changed. Please note that these GOSTs allow you to modify the specification form, change dimensions, add additional columns (except for the dimensions of the main inscription column and additional columns to it) in accordance with enterprise standards.
The archive contains the given GOSTs, as well as specifications, made according to these GOSTs in dwg format.
GOST 21.110-2013
INTERSTATE STANDARD
System of design documents for construction
SPECIFICATIONS OF EQUIPMENT, PRODUCTS AND MATERIALS
System of design documents for construction. Specification of equipment, products and materials
ISS 01.100.30
Date of introduction 2015-01-01
Preface
Preface
The goals, basic principles and basic procedure for carrying out work on interstate standardization are established in GOST 1.0-2015 "Interstate standardization system. Basic provisions" and GOST 1.2-2015 "Interstate standardization system. Interstate standards, rules and recommendations for interstate standardization. Rules for development, adoption , updates and cancellations"
Standard information
1 DEVELOPED by the Open Joint Stock Company "Center for Methodology of Standardization and Standardization in Construction" (JSC "CNS")
2 INTRODUCED by the Technical Committee TC 465 "Construction"
3 ADOPTED by the Interstate Council for Standardization, Metrology and Certification (IGS) (protocol dated November 14, 2013 N 44)
The following voted for adoption:
Short name of the country | Abbreviated name of the national standardization body |
|
Azerbaijan | Azstandard |
|
Ministry of Economy of the Republic of Armenia |
||
Belarus | State Standard of the Republic of Belarus |
|
Kazakhstan | Gosstandart of the Republic of Kazakhstan |
|
Kyrgyzstan | Kyrgyzstandard |
|
Moldova-Standard |
||
Rosstandart |
||
Tajikistan | Tajikstandard |
|
Uzbekistan | Uzstandard |
4 By Order of the Federal Agency for Technical Regulation and Metrology dated December 17, 2013 N 2310-st, the interstate standard GOST 21.110-2013 was put into effect as a national standard of the Russian Federation on January 1, 2015.
5 INSTEAD GOST 21.110-95
6 REPUBLICATION. January 2019
Information about changes to this standard is published in the annual information index "National Standards", and the text of changes and amendments is published in the monthly information index "National Standards". In case of revision (replacement) or cancellation of this standard, the corresponding notice will be published in the monthly information index "National Standards". Relevant information, notices and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet (www.gost.ru)
1 area of use
This standard establishes the form and general rules for the implementation of specifications of equipment, products and materials as part of working documentation for the construction of facilities for various purposes.
2 Normative reference
This standard uses reference to the following interstate standard:
GOST 21.101-97 * System of design documentation for construction. Basic requirements for design and working documentation
________________
* GOST R 21.1101-2013 is in force in the Russian Federation.
Note - When using this standard, it is advisable to check the validity of the reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or using the annual information index "National Standards", which was published as of January 1 of the current year, and on issues of the monthly information index "National Standards" for the current year. If the reference standard is replaced (changed), then when using this standard you should be guided by the replacing (changed) standard. If the reference standard is canceled without replacement, then the provision in which a reference is made to it is applied in the part that does not affect this reference.
3 Terms and definitions
In this standard, the following term is used with the corresponding definition:
3.1 specification of equipment, products and materials: A textual design document that defines the composition of equipment, products and materials and is intended for acquisition, preparation and implementation of construction.
4 General requirements
4.1 The specification of equipment, products and materials (hereinafter referred to as the specification) is drawn up in Form 1 for all main sets of working drawings, except for the main sets of working drawings of structural solutions (reinforced concrete, metal and wooden structures).
If the main set of working drawings of one brand is divided into several sets of the same brand, then a specification is drawn up for each of these sets.
It is allowed to modify the specification form, for example, to include additional columns in it, to change the size of the columns (except for the size of the columns of the main inscription and additional columns to it), in accordance with the requirements established in the standards of organizations.
It is allowed not to print horizontal lines delimiting specification lines, but it is necessary to maintain an interval of at least one printing digit between the texts of adjacent lines.
4.2 The specification is carried out on paper and/or in the form of an electronic document.
The specification in the form of an electronic document in the content part must contain all the data necessary for its output to information display media or on paper in accordance with the requirements of this standard.
4.3 The specification includes all equipment, materials and products provided for in the working drawings of the corresponding main set.
4.4 If an industrial building (structure) has attached or built-in parts in which auxiliary premises are located, then the specification is drawn up in parts, for example:
- production part;
- auxiliary part.
If a residential building has attached or built-in parts to accommodate enterprises and public institutions, then the specification is also drawn up in parts:
- residential part;
- auxiliary part.
4.5 The specification or its parts are usually compiled into sections and, if necessary, subsections. Within each section (subsection), equipment, products and materials are placed into groups, and within groups - in ascending order of their main parameters (for example, type, brand, diameter, cross-section, overall dimensions, etc.).
The specific composition of sections and subsections of the specification and the sequence of recording equipment, products and materials in them are established in the standards of the Construction Design Documentation System (SPDS) for types of construction and installation work.
The names of parts, sections and subsections are written in the column “Name and technical characteristics” in the form of a heading, symmetrical to the text, and underlined. In this case, the section and subsection headings should be separated from the text by an interval of one or two lines. The title may not be underlined.
4.6 The specification does not include certain types of products and materials, the nomenclature and quantity of which are determined by the construction and installation organization, based on current technological and production standards.
4.7 The specification indicates:
- in the column "Pos." - positional designations* of equipment and products provided for in the working drawings of the corresponding main set;
________________
* The designator may be numeric or alphanumeric.
- in the column “Name and technical characteristics” - names of equipment, products, materials, their technical characteristics in accordance with the requirements of standards, technical specifications and other technical documentation, as well as other necessary information. When recording a material, indicate its symbol established in the standard or other regulatory document. Before the name of equipment, products and materials, indicate their serial number of entry in the specification (usually within the section).
In a specification made in electronic form, the horizontal line included in the designation of materials (rolled products, pipes, etc.) can be replaced with a slash (/):
- in the column “Type, brand, designation of document, questionnaire” - type, brand of equipment, product, designation of a standard, technical specifications or other document, as well as designation of the questionnaire**, if the ordering procedure requires the preparation of questionnaires;
________________
** The forms of questionnaires are established by the manufacturer of the equipment or product.
- in the column “Product code” - the code of the product (equipment, product, material) according to the product classifier of the country that developed the working documentation***. If standards, technical specifications, catalogs and other documents for products do not contain information on product codes, then this column is not filled in;
________________
*** Product codes according to product classifiers of other countries are not indicated.
In the "Supplier" column - the name (address) of the manufacturer or supplier of the equipment (for imported equipment - country, company);
- in the column "Unit of measurement" - designation of the unit of measurement;
- in the column "Quantity." - quantity of equipment, products, materials:
- in the column “Weight of 1 unit, kg” - the mass of a unit of equipment, product in kilograms. It is allowed to indicate the weight in tons for heavy equipment. For equipment or products weighing up to 25 kg that do not require the use of lifting and transport vehicles during installation, the column may not be filled in;
- in the "Note" column - additional information.
4.8 In the specification, when recording equipment and individually manufactured products, the columns “Type, brand, designation of document, questionnaire” and “Product code” are not filled in, and in the column “Weight of 1 unit kg” the approximate weight of a piece of equipment is indicated.
4.9 When using imported equipment, products and materials, they are recorded with the names and designations contained in the accompanying technical documentation (delivery documents).
It is allowed to simultaneously indicate authentic designations and names in Russian.
4.10 Specifications of equipment, products and materials are assigned a designation consisting of the designation of the corresponding main set of working drawings in accordance with GOST 21.101 and through the code point “SO”.
Example - 2345-11-TX.SO, 2345-11-OV.SO, 2345-11-ATKH1.SO
4.11 The first sheet of the specification is the title page, made according to form 15* GOST 21.101 on an A4 sheet.
________________
*Form 13 GOST R 21.1101-2013.
Specification sheets are prepared with the following basic inscriptions:
- capital** - according to form 5 GOST 21.101;
________________
** For a text document made with a title page and formatted with main inscriptions, the title page is the next sheet after the title page.
- subsequent ones - according to form 6 GOST 21.101.
It is allowed to omit the title page. In this case, the first sheet of the specification is drawn up with the main inscription according to Form 3 GOST 21.101.
4.12 On the title page the name of the specification is given indicating the name of the corresponding main set of working drawings.
Examples
1 Specification of equipment, products and materials for architectural solutions.
2 Specification of equipment, products and materials for external water supply and sewerage networks.
The name of the document in the title block on the title (first) sheet may be abbreviated as: “Specification of equipment, products and materials.”
4.13 The specification of equipment, products and materials is recorded in the “Attached Documents” section of the list of reference and attached documents, which is included in the general data on the working drawings of the corresponding main set.
Form 1 - Specification of equipment, products and materials
UDC 658.516:002:69:006.354 | ISS 01.100.30 |
Key words: specification of equipment, products and materials, execution rules, working documentation, main set of working drawings, attached documents |
|
Electronic document text
prepared by Kodeks JSC and verified against:
official publication
M.: Standartinform, 2019
Filling out specifications is not a complicated process, but it is very labor-intensive and time-consuming. To prevent your work from going down the drain, you should carefully study and apply the rules for drawing up and filling out the specification.
Here we will look at GOST standards for the design of specifications in projects, in particular:
GOST for specifications
Specifications should be carried out according to — current, updated edition GOST 21.110-95 rules for fulfilling the specifications of equipment, products and materials.
However, the new GOST refers to the outdated GOST for design 21.101-97, where appropriate, I have corrected the links to the current one GOST 21.1101 -2013.
General requirements for filling out equipment specifications
4.1 The specification of equipment, products and materials (hereinafter referred to as the specification) is drawn up in Form 1 for all main sets of working drawings, except for the main sets of working drawings of structural solutions (reinforced concrete, metal and wooden structures).
Equipment specification, form 1 according to GOST 21.110-213
If the main set of working drawings of one brand is divided into several sets of the same brand, then a specification is drawn up for each of these sets.
It is allowed to modify the specification form, for example, to include additional columns in it, to change the size of the columns (except for the size of the columns of the main inscription and additional columns to it), in accordance with the requirements established in the standards of organizations.
It is allowed not to print horizontal lines delimiting specification lines, but it is necessary to maintain an interval of at least one printing digit between the texts of adjacent lines.
4.2 The specification is carried out on on paper and/or in the form of an electronic document.
The specification in the form of an electronic document in the content part must contain all the data necessary for its output to information display media or on paper in accordance with the requirements of this standard.
4.3 The specification includes all equipment, materials and products provided for in the working drawings of the corresponding main set.
4.4 If an industrial building (structure) has attached or built-in parts in which auxiliary premises are located, then the specification is drawn up in parts, for example:
- production part;
- auxiliary part.
If a residential building has attached or built-in parts to accommodate enterprises and public institutions, then the specification is also drawn up in parts:
- residential part;
- auxiliary part.
4.5 The specification or parts thereof are usually compiled according to sections and, if necessary, - subsections. Within each section (subsection) equipment, products and materials are placed according to groups, and within groups- in ascending order of their main parameters
For example: type, brand, diameter, section, overall dimensions, etc.
The specific composition of sections and subsections of the specification and the sequence of recording equipment, products and materials in them are established in the standards of the Construction Design Documentation System (SPDS) for types of construction and installation work.
The names of parts, sections and subsections are written in the column “Name and technical characteristics” in the form of a heading, symmetrical to the text, and underlined. In this case, the section and subsection headings should be separated from the text by an interval of one or two lines. The title may not be underlined.
4.6 The specification does not include certain types of products and materials, the nomenclature and quantity of which are determined by the construction and installation organization, based on current technological and production standards.
The specifications indicate:
- in the column "Pos."- positional designations* of equipment and products provided for in the working drawings of the corresponding main set;
- in the column “Name and technical characteristics”- names of equipment, products, materials, their technical characteristics in accordance with the requirements of standards, technical specifications and other technical documentation, as well as other necessary information. When recording a material, indicate its symbol established in the standard or other regulatory document. Before the name of equipment, products and materials, indicate their serial number of entry in the specification (usually within the section).
* The designator may be numeric or alphanumeric.
In a specification made in electronic form, the horizontal line included in the designation of materials (rolled products, pipes, etc.) can be replaced with a slash (/);
- in the column - the type, brand of equipment, product, designation of the standard, technical specifications or other document, as well as the designation of the questionnaire*, if the ordering procedure requires the preparation of questionnaires;
* The forms of questionnaires are established by the manufacturer of the equipment or product.
- in the column "Product code"- product code (equipment, product, material) according to the product classifier of the country that developed the working documentation**. If standards, technical specifications, catalogs and other documents for products do not contain information on product codes, then this column is not filled in;
** Product codes according to product classifiers of other countries are not indicated.
- in the column "Provider"- name (address) of the manufacturer or supplier of the equipment (for imported equipment - country, company);
- in the column “Unit. measurements"- designation of the unit of measurement;
- in the column "Col."- quantity of equipment, products, materials;
- in the column “Weight of 1 unit, kg”- mass of a unit of equipment, product in kilograms. It is allowed to indicate the weight in tons for heavy equipment. For equipment or products weighing up to 25 kg that do not require the use of lifting and transport vehicles during installation, the column may not be filled in;
- in the column "Note"-additional information.
4.8 In the specification, when recording equipment and custom-made products, columns “Type, brand, designation of document, questionnaire” And "Product code" do not fill out, but in the column “Weight of 1 unit, kg” indicate approximate weight of a piece of equipment.
4.9 When using imported equipment, products and materials, they are recorded with the names and designations contained in the accompanying technical documentation (delivery documents).
It is allowed to simultaneously indicate authentic designations and names in Russian.
4.10 Specifications of equipment, products and materials are assigned a designation consisting of the designation of the corresponding main set of working drawings in accordance with GOST 21.101 and through the code point “SO”.
Example - 2345-11-TX.SO, 2345-11-OV.SO, 2345-11-ATKH1.SO
4.11 The first sheet of the specification is the title page, carried out according to form 13 GOST R 21.1101-2013. on a sheet of A4 format.
Title page, Form 13 according to GOST R 21.1101-2013 Specification sheets are prepared with the following basic inscriptions:
- capital** - by form 5 GOST R 21.1101-2013;
- subsequent - by form 6 GOST R 21.1101-2013.
It is allowed to omit the title page. In this case, the first sheet of the specification is drawn up with the main inscription according to form 3 GOST R 21.1101-2013.
4.12 On the title page the name of the specification is given indicating the name of the corresponding main set of working drawings.
Examples:
- Specification of equipment, products and materials for architectural solutions.
- Specification of equipment, products and materials for external water supply and sewerage networks.
The name of the document in the title block on the title (first) sheet may be abbreviated as: “Specification of equipment, products and materials.”
4.13 The specification of equipment, products and materials is recorded in the “Attached Documents” section of the list of reference and attached documents, which is included in the general data on the working drawings of the corresponding main set.
** For a text document made with a title page and formatted with main inscriptions, the title page is the next sheet after the title page.
Equipment specification according to GOST 21.110 download.
Rules for fulfilling specifications in drawings according to GOST 21.1101-2013
6.1. For layout diagrams of elements of a prefabricated structure, monolithic reinforced concrete structure, for layout drawings of technological equipment and/or pipelines, installations (blocks) of technological, sanitary and other equipment, as well as for other drawings, specifications are drawn up for form 7(Appendix K)
Specification, Form 7 according to GOST R 21.1101-2013 When making drawings using the group method, group specifications are drawn up according to form 8(Appendix K)
Group specification, Form 8 according to GOST R 21.1101-2013 6.2 The specification is usually placed on a sheet of drawings, which shows diagrams, plans for the location of equipment and pipelines, and installation plans. It is allowed to carry out the specification on separate sheets as subsequent sheets of drawings.
6.3 In electronic models, if necessary, specifications and other tables in the drawings may be performed in the working space of the electronic model, taking into account the provisions GOST 2.052. In this case, it is recommended to perform them at a separate information level.
6.4 Specifications for construction products are based on GOST 21.501
The specifications indicate:
- in the column "Pos."— position (brand) of structural elements, installations;
- in the column "Designation"— designations of the main documents for the structural elements, equipment, products or standards (technical conditions) for them recorded in the specification;
- in the column "Name"— name of structural elements, equipment, products, materials and their designations (brands), as well as, if necessary, technical characteristics of equipment and products.
It is allowed to indicate the name once for a group of elements of the same name and underline it.
The specification records materials directly included in the specified structure, product, etc.
In a specification made in electronic form, the horizontal line included in the designation of materials (rolled products, pipes, etc.) can be replaced with a slash (/);
- graph "Col." Form 7- amount of elements.
In the column "Col." forms 8- instead of an ellipsis, write “according to the scheme”, “per floor”, etc., and below - the serial numbers of layout diagrams or floors;
- in the column “Unit mass, kg”- mass in kilograms. It is allowed to give the mass in tons, but indicating the unit of mass;
- in the column "Note"— additional information, for example, unit of mass.
*The dimensions of the specification columns can be changed at the discretion of the developer, if necessary.
**When filling out the specification using an automated method, lines demarcating horizontal lines may not be drawn.
page 1
page 2
page 3
page 4
page 5
page 6
page 7
page 8
page 9
Preface
The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 “Interstate standardization system. Basic provisions" and GOST 1.2-2009 "Interstate standards. Rules and recommendations for interstate standardization. Rules for development, adoption, application, updating and cancellation.”
Standard information
1 DEVELOPED by the Open Joint-Stock Company “Center for Methodology of Standardization and Standardization in Construction” (JSC “CNS”)
2 INTRODUCED by the Technical Committee TC 465 “Construction”
3 ADOPTED by the Interstate Council for Standardization, Metrology and Certification (IGS) (protocol dated November 14, 2013 No. 44-2013)
|
Short name of the country |
Code of the country |
Abbreviated name of the body |
|
Azerbaijan |
Azstandard |
|
|
Ministry of Economy of the Republic of Armenia |
||
|
Belarus |
State Standard of the Republic of Belarus |
|
|
Kazakhstan |
Gosstandart of the Republic of Kazakhstan |
|
|
Kyrgyzstan |
Kyrgyzstandard |
|
|
Moldova-Standard |
||
|
Rosstandart |
||
|
Tajikistan |
Tajikstandard |
|
|
Uzbekistan |
Uzstandard |
4 By Order of the Federal Agency for Technical Regulation and Metrology dated December 17, 2013 No. 2310-st, the interstate standard GOST 21.110-2013 was put into effect as the national standard of the Russian Federation on January 1, 2015.
Information about changes to this standard is published in the annual information index “National Standards”, and the text of changes and amendments is published in the monthly information index “National Standards”. In case of revision (replacement) or cancellation of this standard, the corresponding notice will be published in the monthly information index “National Standards”. Relevant information, notifications and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet.
INTERSTATE STANDARD
System of design documents for construction
SPECIFICATIONS OF EQUIPMENT, PRODUCTS AND MATERIALS
System of design documents for construction.
Specification of equipment, products and materials.
Date of introduction - 2015-01-01
1 area of use
This standard establishes the form and general rules for the implementation of specifications of equipment, products and materials as part of working documentation for the construction of facilities for various purposes.
2 Normative reference
Note - When using this standard, it is advisable to check the validity of the reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or using the annual information index “National Standards”, which was published as of January 1 of the current year, and on issues of the monthly information index “National Standards” for the current year. If the reference standard is replaced (changed), then when using this standard you should be guided by the replacing (changed) standard. If the reference standard is canceled without replacement, then the provision in which a reference is made to it is applied in the part that does not affect this reference.
3 Terms and definitions
In this standard, the following term is used with the corresponding definition:
3.1 specification of equipment, products and materials: A textual design document that defines the composition of equipment, products and materials and is intended for acquisition, preparation and implementation of construction.
4 General requirements
4.1 The specification of equipment, products and materials (hereinafter referred to as the specification) is drawn up in Form 1 for all main sets of working drawings, except for the main sets of working drawings of structural solutions (reinforced concrete, metal and wooden structures).
If the main set of working drawings of one brand is divided into several sets of the same brand, then a specification is drawn up for each of these sets.
It is allowed to modify the specification form, for example, to include additional columns in it, to change the size of the columns (except for the size of the columns of the main inscription and additional columns to it), in accordance with the requirements established in the standards of organizations.
It is allowed not to print horizontal lines delimiting specification lines, but it is necessary to maintain an interval of at least one printing digit between the texts of adjacent lines.
4.2 The specification is carried out on paper and/or in the form of an electronic document.
The specification in the form of an electronic document in the content part must have everything
data necessary for its output on information display media or on paper in accordance with the requirements of this standard.
4.3 The specification includes all equipment, materials and products provided for in the working drawings of the corresponding main set.
4.4 If an industrial building (structure) has attached or built-in parts in which auxiliary premises are located, then the specification is drawn up in parts, for example:
Production part;
Auxiliary part.
If a residential building has attached or built-in parts to accommodate enterprises and public institutions, then the specification is also drawn up in parts:
Residential part;
Auxiliary part.
4.5 The specification or its parts are usually compiled into sections and, if necessary, subsections. Within each section (subsection), equipment, products and materials are placed into groups, and within groups - in ascending order of their main parameters (for example: type, brand, diameter, cross-section, overall dimensions, etc.).
The specific composition of sections and subsections of the specification and the sequence of recording equipment, products and materials in them are established in the standards of the Construction Design Documentation System (SPDS) for types of construction and installation work.
The names of parts, sections and subsections are written in the column “Name and technical characteristics” in the form of a heading, symmetrical to the text, and underlined. In this case, the section and subsection headings should be separated from the text by an interval of one or two lines. The title may not be underlined.
4.6 The specification does not include certain types of products and materials, the nomenclature and quantity of which are determined by the construction and installation organization, based on current technological and production standards.
4.7 The specification indicates:
In the column "Pos." - positional designations * of equipment and products provided for in the working drawings of the corresponding main set;
* The designator may be numeric or alphanumeric.
In the column “Name and technical characteristics” - names of equipment, products, materials, their technical characteristics in accordance with the requirements of standards, technical specifications and other technical documentation, as well as other necessary information. When recording a material, indicate its symbol established in the standard or other regulatory document. Before the name of equipment, products and materials, indicate their serial number of entry in the specification (usually within the section).
In a specification made in electronic form, the horizontal line included in the designation of materials (rolled products, pipes, etc.) can be replaced with a slash (/);
In the column “Type, brand, designation of a document, questionnaire” - the type, brand of equipment, product, designation of a standard, technical specifications or other document, as well as the designation of a questionnaire * if the ordering procedure requires the preparation of questionnaires;
* The forms of questionnaires are established by the manufacturer of the equipment or product.
In the column “Product code” - the code of the product (equipment, product, material) according to the product classifier of the country that developed the working documentation **. If standards, technical specifications, catalogs and other documents for products do not contain information on product codes, then this column is not filled in;
** Product codes according to product classifiers of other countries are not indicated.
In the “Supplier” column - the name (address) of the manufacturer or supplier of the equipment (for imported equipment - country, company);
In the column “Unit. measurement" - designation of the unit of measurement;
In the column "Count." - quantity of equipment, products, materials;
In the column “Weight of 1 unit, kg” - the mass of a unit of equipment, product in kilograms. It is allowed to indicate the weight in tons for heavy equipment. For equipment or products weighing up to 25 kg that do not require the use of lifting and transport vehicles during installation, the column may not be filled in;
In the “Note” column there is additional information.
4.8 In the specification, when recording equipment and individually manufactured products, the columns “Type, brand, designation of document, questionnaire” and “Product code” are not filled in, and in the column “Weight of 1 unit, kg” the approximate weight of a unit of equipment is indicated.
4.9 When using imported equipment, products and materials, they are recorded with the names and designations contained in the accompanying technical documentation (delivery documents).
It is allowed to simultaneously indicate authentic designations and names in Russian.
4.10 Specifications of equipment, products and materials are assigned a designation consisting of the designation of the corresponding main set of working drawings in accordance with GOST 21.101 and through the code point “SO”.
Example - 2345-11-TX.SO, 2345-11-OV.SO, 2345-11-ATKH1.SO
4.11 The first sheet of the specification is the title page, made according to form 15 * GOST 21.101 on a sheet of A4 format. GOST 21.101.
4.12 On the title page the name of the specification is given indicating the name of the corresponding main set of working drawings.
Examples
1 Specification of equipment, products and materials for architectural solutions.
2 Specification of equipment, products and materials for external water supply and sewerage networks.
The name of the document in the title block on the title (first) sheet may be abbreviated as: “Specification of equipment, products and materials.”
4.13 The specification of equipment, products and materials is recorded in the “Attached Documents” section of the list of reference and attached documents, which is included in the general data on the working drawings of the corresponding main set.
Form 1 - Specification of equipment, products and materials
Key words: specification of equipment, products and materials, execution rules, working documentation, main set of working drawings, attached documents
INTERSTATE COUNCIL FOR STANDARDIZATION. METROLOGY AND CERTIFICATION
INTERSTATE COUNCIL FOR STANDARDIZATION. METROLOGY AND CERTIFICATION
INTERSTATE STANDARD 21.110-
System of design documents for construction
SPECIFICATIONS OF EQUIPMENT, PRODUCTS AND MATERIALS
Official publication
Standardinform
GOST 21.110-2013
Preface
The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 “Interstate standardization system. Basic provisions" and GOST 1.2-2009 "Interstate standards. Rules and recommendations for interstate standardization. Rules for development, adoption, application, updating and cancellation.”
Swadonia about the standard
1 DEVELOPED by the Open Joint-Stock Company “Center for Methodology of Standardization and Standardization in Construction” (JSC “CNS”)
2 INTRODUCED by the Technical Committee TC 465 “Construction”
3 ADOPTED by the Interstate Council for Standardization, Metrology and Certification (IGS) (protocol dated November 14, 2013 No. 44-2013)
| Short name of the country according to MK (ISO 3166) 004-97 |
Country code according to MK (ISO 3166) 004-97 |
Abbreviated name of the state construction management body |
| Azerbaijan |
Azstandard |
|
| Ministry of Economy of the Republic of Armenia |
||
| Belarus |
State Standard of the Republic of Belarus |
|
| Kazakhstan |
Gosstandart of the Republic of Kazakhstan |
|
| Kyrgyzstan |
Kyrgyzstandard |
|
| Moldova-Standard |
||
| Rosstandart |
||
| Tajikistan |
Tajikstandard |
|
| Uzbekistan |
Uzstandard |
4 By Order of the Federal Agency for Technical Regulation and Metrology dated December 17, 2013 No. 2310-st, the interstate standard GOST 21.001-2013 was put into effect as the national standard of the Russian Federation from January 1, 2015. 5 INSTEAD GOST 21.110-95
Information about changes to this standard is published in the annual information index “National Standards”, and the text of changes and amendments is published in the monthly information index “National Standards”. In case of revision (replacement) or cancellation of this standard, the corresponding notice will be published in the monthly information index “National Standards”. Relevant information, notifications and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet.
© Standardinform, 2014
In the Russian Federation, this standard cannot be fully or partially reproduced, replicated and distributed as an official publication without permission from the Federal Agency for Technical Regulation and Metrology
GOST 21.110-2013
INTERSTATE STANDARD
System of design documentation for construction SPECIFICATIONS OF EQUIPMENT, PRODUCTS AND MATERIALS
System of design documents for construction.
Specification of equipment, products and materials.
Date of introduction - 2015-01-01
1 area of use
This standard establishes the form and general rules for the implementation of specifications of equipment, products and materials as part of working documentation for the construction of facilities for various purposes.
Official publication
GOST 21.110-2013
4 General requirements
4.1 The specification of equipment, products and materials (hereinafter referred to as the specification) is drawn up in Form 1 for all main sets of working drawings, except for the main sets of working drawings of structural solutions (reinforced concrete, metal and wooden structures).
If the main set of working drawings of one brand is divided into several sets of the same brand, then a specification is drawn up for each of these sets.
It is allowed to modify the specification form, for example, to include additional columns in it, to change the size of the columns (except for the size of the columns of the main inscription and additional columns to it), in accordance with the requirements established in the standards of organizations.
It is allowed not to print horizontal lines delimiting specification lines, but it is necessary to maintain an interval of at least one printing digit between the texts of adjacent lines.
4.2 The specification is carried out on paper and/or in the form of an electronic document.
The specification in the form of an electronic document in the content part must have everything
data necessary for its output on information display media or on paper in accordance with the requirements of this standard.
4.3 The specification includes all equipment, materials and products provided for in the working drawings of the corresponding main set.
4.4 If an industrial building (structure) has attached or built-in parts in which auxiliary premises are located, then the specification is drawn up in parts, for example:
* production part;
Auxiliary part.
If a residential building has attached or built-in parts to accommodate enterprises and public institutions, then the specification is also drawn up in parts:
Residential part;
Auxiliary part.
4.5 The specification or its parts are usually compiled into sections and. if necessary, - subsections. Within each section (subsection), equipment, products and materials are placed into groups, and within groups - in ascending order of their main parameters (for example: type, brand, diameter, cross-section, overall dimensions, etc.).
The specific composition of sections and subsections of the specification and the sequence of recording equipment, products and materials in them are established in the standards of the System of Design Documentation for Construction (SG1DS) by type of construction and installation work.
The names of parts, sections and subsections are written in the column “Name and technical characteristics” in the form of a heading, symmetrical to the text, and underlined. In this case, the section and subsection headings should be separated from the text by an interval of one or two lines. The title may not be underlined.
4.6 The specification does not include certain types of products and materials, the nomenclature and quantity of which are determined by the construction and installation organization, based on current technological and production standards.
4.7 Indicate in the specification.
In the column "Pos." - positional designations* of equipment and products provided for in the working drawings of the corresponding main set;
In the column “Name and technical characteristics” - names of equipment, products, materials, their technical characteristics in accordance with the requirements of standards, technical specifications and other technical documentation, as well as other necessary information. When recording a material, indicate its symbol established in the standard or other regulatory document. Before the name of equipment, products and materials, indicate their serial number of entry in the specification (usually within the section).
The designator may be numeric or alphanumeric.
GOST 21.110-2013
In a specification made in electronic form, a horizontal line included in the designation of materials (rolled products, pipes, etc.). may be replaced with a slash (/);
In the column “Type. brand, designation of document, questionnaire” - type. brand of equipment, product, designation of a standard, technical specifications or other document, as well as designation of a questionnaire*, if the ordering procedure requires the preparation of questionnaires;
In the column “Product code” - the code of the product (equipment, product, material) according to the product classifier of the country that developed the working documentation**. If standards, technical specifications, catalogs and other documents for products do not contain information on product codes, then this column is not filled in;
In the “Supplier” column - the name (address) of the manufacturer or supplier of the equipment (for imported equipment - country, company);
In the column “Unit. measurement" - designation of the unit of measurement;
In the column "Count." - quantity of equipment, products, materials;
In the column “Weight of 1 unit. kg” - the mass of a unit of equipment, product in kilograms. It is allowed to indicate the weight in tons for heavy equipment. For equipment or products weighing up to 25 kg that do not require the use of lifting vehicles during installation, the column may not be filled in;
In the “Note” column there is additional information.
4.8 In the specification, when recording equipment and individually manufactured products, the columns “Type, brand, designation of document, questionnaire” and “Product code” are not filled in, and in the column “Weight of 1 unit kg” the approximate weight of a unit of equipment is indicated.
4.9 When using imported equipment, products and materials, they are recorded with the names and designations contained in the accompanying technical documentation (delivery documents).
It is allowed to simultaneously indicate authentic designations and names in Russian
* The forms of questionnaires are established by the manufacturer of the equipment or product.
** Product codes according to product classifiers of other countries are not indicated.
4.10 Specifications of equipment, products and materials are assigned a designation consisting of the designation of the corresponding main set of working drawings in accordance with GOST 21.101 and through the code point “SO”.
Example - 2345-11-TX.SO, 2345-11-OV.SO, 2345-11-ATKH1.SO
4.11 The first sheet of the specification is the title page, made according to form 15* GOST 21.101 on an A4 sheet.
Specification sheets are prepared with the following basic inscriptions:
Capital** - according to form 5 GOST 21.101;
Subsequent ones - according to form 6 GOST 21.101.
A title page is allowed but fulfilled. In this case, the first sheet of the specification is drawn up with the main inscription according to Form 3 GOST 21.101.
4.12 On the title page the name of the specification is given indicating the name of the corresponding main set of working drawings.
1 Specification of equipment, products and materials for architectural solutions.
2 Specification of equipment, products and materials for external water supply and sewerage networks.
The name of the document on the title block on the title (first) sheet may be abbreviated as: “Specification of equipment, products and materials.”
4.13 The specification of equipment, products and materials is recorded in the “Attached Documents” section of the list of reference and attached documents, which is included in the general data on the working drawings of the corresponding main set.
Prepared based on the electronic version provided by the developer of the standard
FSUE "STANDARTINFORM"
123995 Moscow. Granatny Lane.. 4. www.gostinfo.ru [email protected]
